Notice that the PPTP local address is the same as the router's address on the local interface and the remote address is from the same range as the local network (10.1.101.0/24). Next step is to enable the PPTP server and the PPTP client on the laptop. /interface pptp-server server set enabled=yes

Here's how you can enable support for PPTP VPN connections in iOS 10 after Apple discontinued support for it in the firmware. There are all kinds of reasons that you might want to use a VPN, and while they are not all privacy based, the recent goings on in the world of politics in the United States may be a good reason to look into setting up a good VPN, just in case. A. To enable VPN tunnels between individual host computers or entire networks that have a firewall between them, you must open the following ports:. PPTP. To allow PPTP tunnel maintenance traffic, open TCP 1723. To allow PPTP tunneled data to pass through router, open Protocol ID 47. PPTP utilizes the GRE (Generic Routing Encapsulation) protocol for its point-to-point tunnel. As a pure IP protocol GRE uses only IP addresses but no port numbers giving the router's NAT a tough time to track such a connection. In its base configuration OpenWrt Backfire is able to NAT a single PPTP connections but not multiple such connections concurrently. Before you begin, please make sure that: You must have an active internet connection. VPN Supported Router. Own a premium Ivacy account (If you do not already own one, you can buy a subscription from here)To configure Ivacy using PPTP, please follow the given instructions: Access your router control panel and click on 'WAN' under 'Advance settings' … - Enable VPN passthrough on your router (if your router has that option) - Forward port 1723 tcp and Protocol 47 (GRE) for PPTP - Forward port 500 and 4500 udp and Protocol 50 (ESP) for L2TP. Unfortunately not all of this is supported by every router. Intrinsically, the Point-to-Point Tunneling Protocol and NAT do not work in tandem. Note that most VPN connections begin right behind the router, hence traversing a NAT becomes an issue. PPTP passthrough comes in to allow a VPN network to cross over the NAT with ease. NAT or PAT doesn't work without ports. These IOS commands are applicable to all platforms that support PPTP. 2621#configure terminal Enter configuration commands, one per line. End with CNTL/Z. !--- Enable virtual private dial-up networking. 2621(config)#vpdn enable!--- Enters VPDN group configuration mode for the specified VPDN group. 2621(config)#vpdn-group 1!---

Notice that the PPTP local address is the same as the router's address on the local interface and the remote address is from the same range as the local network (10.1.101.0/24). Next step is to enable the PPTP server and the PPTP client on the laptop. /interface pptp-server server set enabled=yes

Configure PPTP Server PPTP IP Range. Step 1. Log in to the web configuration utility and choose VPN > PPTP Server. The PPTP Server page opens: Step 2. Check the Enable check box to enable the PPTP Server on the RV320. Step 3. Enter the starting LAN IP address of the range assigned to the first PPTP VPN client in the Range Start field. The

Before you begin, please make sure that: You must have an active internet connection. VPN Supported Router. Own a premium Ivacy account (If you do not already own one, you can buy a subscription from here)To configure Ivacy using PPTP, please follow the given instructions: Access your router control panel and click on 'WAN' under 'Advance settings' …

Intrinsically, the Point-to-Point Tunneling Protocol and NAT do not work in tandem. Note that most VPN connections begin right behind the router, hence traversing a NAT becomes an issue. PPTP passthrough comes in to allow a VPN network to cross over the NAT with ease. NAT or PAT doesn't work without ports. These IOS commands are applicable to all platforms that support PPTP. 2621#configure terminal Enter configuration commands, one per line. End with CNTL/Z. !--- Enable virtual private dial-up networking. 2621(config)#vpdn enable!--- Enters VPDN group configuration mode for the specified VPDN group. 2621(config)#vpdn-group 1!---